View RV5VH_362137.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DC/DC CONVERTER CONTROLLER
RV5VH SERIES
APPLICATION MANUAL
NO. EA-049-0006
DC/DC CONVERTER CONTROLLER
RV5VH SERIES
OUTLINE
Each of the RV5VH series is dual output CMOS DC/DC converter ICs integrating Step-up and inverting DC/DC converters. The RV5VH3xx series ICs consists of an oscillator, two VFM control circuits, control transistors(EXT switches), a phase shift circuit, a voltage reference unit, an error amplifier, and voltage sensing resistors. The package for the RV5VH series is 8pin SSOP(0.65mm pitch), and it is suitable for power supply systems with positive and negative output, such as pager, PDA, which need power supplies for LCD. RV5VH1xx and RV5VH2xx series are able to provide two DC/DC converters, one is a step-up DC/DC converter with internally fixed output and the other is an inverting DC/DC converter with adjustable output by external resistors. A voltage detector with sensing pin is also included. RV5VH3xx series are able to provide two DC/DC converters, both of them require external drivers, DC/DC1, and inverting one, DC/DC2, can be adjustable by resistors.
FEATURES
* Dual DC/DC converter system .................................DC/DC1 : step-up DC/DC2 : inverting(negative voltage) ..........................................................Nch. Open Drain Output * Voltage Detector * Low voltage operation available RV5VH1xx,RV5VH2xx ..........................................oscillator start-up from 0.8V RV5VH3xx.................................................................oscillator start-up from 1.8V * High Efficiency .............................................................TYP. 80% * Low Supply Current * High accuracy feedback sensing ...............................TYP. 2.5% * Sleep Mode RV5VH1xx, RV5VH2xx..........................................DC/DC 2 RV5VH3xx.................................................................DC/DC1, 2 * Available to adjust temperature drift .........................DC/DC2 : with external resistor (RV5VH2xx, RV5VH3xx) coefficient of output voltage * Small Package ..............................................................8pin SSOP(0.65mm pitch)
APPLICATIONS
* Power source for telecommunication systems * Power source for portable data processing systems, e.g. PDA, Electronic Data Banks * Power source for Audio-Visual systems, e.g. CD players, Video cameras * Power source for Notebook PCs, Word processing systems * Gadgets which need two power supplies, e.g. CPU and LCD
1
DC/DC CONVERTER CONTROLLER (BOOST / INVERTING)
RV5VH1xx/ RV5VH2xx
BLOCK DIAGRAM
* RV5VH1xx
CSW 1
- +
8 DOUT
VSEN 2
Vref Error Amp.2 Error Amp.1 - + VLX lim.
- +
7 FB
VOUT1 3
VFM2
6 EXT2
LX1 4 VFM1
p_shift
5 GND OSC
* RV5VH2xx
CSW 1
- +
8 DOUT
VSEN 2
Vref Error Amp.2 Error Amp.1 - +
- +
7 FB
VOUT1 3
VFM2
6 EXT2
EXT1 4 VFM1
p_shift
5 GND OSC
2
RV5VH1xx/RV5VH2xx
PIN CONFIGURATION
* 8 pin SSOP (0.65mm pitch)
1 2 3 4 8 7 6 5
PIN DESCRIPTION
* RV5VH1xx
Pin No. Symbol Description
1 2 3 4 5 6 7 8
CSW VSEN VOUT1 LX1 GND EXT2 FB DOUT
Control switch for DC/DC2 Sensing Pin for Voltage Detector Output for DC/DC1, Power supply for the device Output for DC/DC1, switching (Nch Open-Drain) Ground External Transistor drive pin for DC/DC2 (CMOS output) Input for DC/DC2 Error Amplifier Output for Voltage detector
* RV5VH2xx
Pin No. Symbol Description
1 2 3 4 5 6 7 8
CSW VSEN VOUT1 EXT1 GND EXT2 FB DOUT
Contol switch for DC/DC2 Sensing Pin for Voltage Detector Output for DC/DC1, Power supply for the device External Transistor drive pin for DC/DC1 (CMOS output) Ground External Transistor drive pin for DC/DC2 (CMOS output) Input for DC/DC2 Error Amplifier Output for Voltage Detector
3
RV5VH1xx/RV5VH2xx
ABSOLUTE MAXIMUM RATINGS
* RV5VH1xx
Symbol Item Ratings Unit
VOUT1 VLX1 VSEN DOUT VCSW VEXT2 VFB ILX1 IEXT2 PD Topt Tstg Tsolder
VOUT1 Pin Voltage LX1 Pin Voltage VSEN Pin Voltage DOUT Pin Voltage CSW Pin Voltage EXT2 Pin Voltage FB Pin Voltage LX1 Output Current EXT2 Output Current Power Dissipation Operating Temperature Storage Temperature Lead Temperature (Soldering)
12 12 12 12 -0.3 to VOUT1 +0.3 -0.3 to VOUT1 +0.3 -0.3 to VOUT1 +0.3 400 50 300 -40 to +85 -55 to +125 260C 10sec
V V V V V V V mA mA mW C C
4
RV5VH1xx/RV5VH2xx
* RV5VH2xx
Symbol Item Ratings Unit
VOUT1 VSEN DOUT VCSW VEXT1, 2 VFB IEXT1, 2 PD Topt Tstg Tsolder
VOUT1 Pin Voltage VSEN Pin Voltage DOUT Pin Voltage CSW Pin Voltage EXT1, 2 Pin Voltage FB Pin Voltage EXT1, 2 Output Current Power Dissipation Operating Temperature Storage Temperature Lead Temperature (Soldering)
12 12 12 -0.3 to VOUT1 +0.3 -0.3 to VOUT1 +0.3 -0.3 to VOUT1 +0.3 50 300 -40 to +85 -55 to +125 260C 10sec
V V V V V V mA mW C C
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum ratings are threshold limit values that must not be exceeded even for an instant under any conditions. Moreover, such values for any two items must not be reached simultaneously. Operation above these absolute maximum ratings may cause degradation or permanent damage to the device. These are stress ratings only and do not necessarily imply functional operation below these limits.
5
RV5VH1xx/RV5VH2xx
ELECTRICAL CHARACTERISTICS
* RV5VH101 DC/DC Converter 1
Symbol Item Conditions MIN. TYP.
VOUT1=3.0V, Topt=25C
MAX.
Unit
VOUT1 VINmax Vstart Vhold ISS1 ILX ILXleak fosc Maxdty VLXlim VOUT1 Topt
Step-up Output Voltage Maximum Input Voltage Oscillator Start-up Voltage Hold-on Input Voltage Supply Current1 *1 LX Switching Current LX Leakage Current Maximum Oscillator Frequency Oscillator Duty Cycle Efficiency Voltage Limit for LX Switch Output Voltage Temp. Coefficient for LX pin -40CTopt85C ON (VLX="L") No Load IOUT=1mA, VIN : 20V No Load, CSW="L" VLX=0.4V VLX=6.0V, VIN=3.5V
2.925
3.000
3.075 10
V V V V
0.7 0.7 10 100 0.03 110 50 130 65 80 0.4 100
0.8
A mA 1 150 80 A kHz % % 0.8 V ppm/C
* ) VIN=1.2V, IOUT=10mA, Topt=25C, unless otherwise specified. (See Typical Application) *1 ) This value only shows the supply current of DC/DC1, not include the supply current of Voltage Detector and external resistors.
6
RV5VH1xx/RV5VH2xx
DC/DC Converter 2
Symbol Item Conditions MIN. TYP.
VOUT1=3.0V, Topt=25C
MAX.
Unit
VSET VFB VIN VOPTmin ISS2 Istandby IEXT2H IEXT2L fosc Maxdty VCSWH VCSWL ICSWleak VFB Topt
Set Output Voltage Feed Back Voltage Maximum Input Voltage Minimum Operating Voltage Supply Current2 Standby Current EXT2 "H" Output Current EXT2 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle CSW "H" Input Voltage CSW "L" Input Voltage CSW Input Leakage Current Feed Back Voltage Temp.Coefficient VEXT2="H" VOUT1=3.0V VOUT1=3.0V VOUT1=3.0V -40CTopt85C IOUT=1mA CSW= "H" at No Load
*1 -20 0
0 20 10 1.8 10 0.3
V mV V V A A mA mA
CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V 2 4 110 40 1.6 0 -0.5
4 8 130 50 150 60 VOUT1 0.4 0.5 30
kHz % V V A V/C
* ) VOUT1=3.0V, IOUT=1mA, Topt=25C, unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors to -30V.
7
RV5VH1xx/RV5VH2xx
Voltage Detector
VOUT1=3.0V, Topt=25C
Symbol
Item
Conditions
MIN.
TYP.
MAX.
Unit
VDET VHYS ISS3 VINmax VOPTmin IOUT ISEN VSEN
Detector Threshold Detector Threshold Hysteresis Supply Current3 Maximum Input Voltage Minimum Operating Voltage VDS=0.5V, VOUT1=1.5V Output Current VDS=0.5V, VOUT1=3.0V Sensing pin Input Current Sensing pin Input Voltage Output Delay Detector Threshold Temp.Coefficient DOUT Leakage Current -40CTopt85C VSEN=3.0V
2.633 0.081
2.700 0.135 1.2
2.767 0.189
V V A
10 1.8 1.0 4.0 2.0 5.0 0.3 0.7 1.2 10 100 100 0.03 0.5
V V mA mA A V s ppm/C A
tPLH
VOUT1 Topt IDOUTleak
* ) VOUT1=3.0V, Topt=25C, unless otherwise specified. (See Typical Application)
8
RV5VH1xx/RV5VH2xx
* RV5VH102 DC/DC Converter 1
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VOUT1 VINmax Vstart Vhold ISS1 ILX ILXleak fosc Maxdty VLXlim VOUT1 Topt
Step-up Output Voltage Maximum Input Voltage Oscillator Start-up Voltage Hold-on Input Voltage Supply Current1 *1 LX Switching Current LX Leakage Current Maximum Oscillator Frequency Oscillator Duty Cycle Efficiency Voltage Limit for LX Switch Output Voltage Temp. Coefficient -40CTopt85C ON (VLX="L") No Load IOUT=1mA, VIN : 20V No Load, CSW="L" VLX=0.4V VLX=6.0V, VIN=5.5V
4.875
5.000
5.125 10
V V V V
0.7 1.2 15 100 0.03 110 55 130 70 80 0.4 100
0.8
A mA 1 150 85 A kHz % % 0.8 V ppm/C
* ) VIN=1.2V, IOUT=10mA, Topt=25C, unless otherwise specified. (See Typical Application) *1 ) This value only shows the supply current of DC/DC1, not include the supply current of Voltage Detector and external resistors.
9
RV5VH1xx/RV5VH2xx
DC/DC Converter 2
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VSET VFB VIN VOPTmin ISS2 Istandby IEXT2H IEXT2L fosc Maxdty VCSWH VCSWL ICSWleak VFB Topt
Set Output Voltage Feed Back Voltage Maximum Input Voltage Minimum Operating Voltage Supply Current2 Standby Current EXT2 "H" Output Current EXT2 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle CSW "H" Input Voltage CSW "L" Input Voltage CSW Input Leakage Current Feed Back Voltage Temp.Coefficient VEXT2="H" VOUT1=5.0V VOUT1=5.0V VOUT1=5.0V -40CTopt85C IOUT=1mA CSW= "H" at No Load
*1
-3.000 0
0
V mV
10 1.8 25 0.3 3 7 110 40 1.6 0 -0.5 30 6 14 130 50 150 60 VOUT1 0.4 0.5
V V A A mA mA kHz % V V A V/C
CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V
* ) VOUT1=3.0V, IOUT=1mA, Topt=25C, unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors to -30V.
10
RV5VH1xx/RV5VH2xx
Voltage Detector
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VDET VHYS ISS3 VINmax VOPTmin IOUT ISEN
Detector Threshold Detector Threshold Hysteresis Supply Current3*1 Maximum Input Voltage Minimum Operating Voltage*2 VDS=0.5V, VOUT1=1.5V Output Current VDS=0.5V, VOUT1=5.0V Sensing Pin Input Current Output Delay DetectorThreshold Temp.Coefficient DOUT Leakage Current -40CTopt85C VSEN=5.0V
4.388 0.135
4.500 0.225 1.8
4.612 0.315
V V A
10 1.8 1.0 7.0 2.0 10.0 0.7 2.0 100 100 0.03 0.5
V V mA mA A s ppm/C A
tPLH
VOUT1 Topt IDOUTleak
* ) VOUT1=3.0V, Topt=25C, unless otherwise specified. (See Typical Application)
11
RV5VH1xx/RV5VH2xx
* RV5VH201 DC/DC Converter 1
Symbol Item Conditions MIN. TYP.
VOUT1=3.0V, Topt=25C
MAX.
Unit
VOUT1 VINmax Vstart Vhold ISS1 IEXT1H IEXT1L fosc Maxdty VOUT1 Topt
Step-up Output Voltage Maximum Input Voltage Oscillator Start-up Voltage Hold-on Input Voltage Supply Current1 *1 EXT1 "H" Output Current EXT1 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle Output Voltage Temp. Coefficient
IOUT=0mA
2.925
3.000
3.075 10
V V V V
No Load IOUT=1mA IOUT=0mA, CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V 1.5 4 110 ON (VLX="L") -40CTopt85C 50 0.7
0.7
0.8
80 3 8 130 65 100 150 80
A mA mA kHz % ppm/C
* ) VIN=1.2V, IOUT=10mA, unless otherwise specified. (See Typical Application) *1 ) This value shows only the supply current of DC/DC1, not include the supply current of Voltage Detector and external resistors.
12
RV5VH1xx/RV5VH2xx
DC/DC Converter 2
Symbol Item Conditions MIN. TYP.
VOUT1=3.0V, Topt=25C
MAX.
Unit
VSET VFB VIN VOPTmin ISS2 Istandby IEXT2H IEXT2L fosc Maxdty VCSWH VCSWL ICSWleak VFB Topt
Output Voltage Setting Range Feed Back Voltage Maximum Input Voltage Minimum Operating Voltage*2 Supply Current2*3 Standby Current EXT2 "H" Output Current EXT2 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle CSW "H" Input Voltage CSW "L" Input Voltage CSW Input Leakage Current Feed Back Voltage Temp. Coefficient VEXT2="H" VOUT1=3.0V VOUT1=3.0V CSW=3.0V -40CTopt85C IOUT=1mA CSW= "H" IOUT=0mA
*1 -20 0
0 20 10 1.8 10 0.3
V mV V V A A mA mA
CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V 2 4 110 40 1.6 0 -0.5
4 8 130 50 150 60 VOUT1 0.4 0.5 30
kHz % V V A V/C
* ) VOUT1=3.0V, VOUT2=-0.3V, IOUT2=1mA, unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors to -30V. *2 ) "Minimum Operating Voltage"means a voltage for the "VOUT1" pin. *3 ) This value shows only the supply current of DC/DC2, not include the supply current of external resistors.
13
RV5VH1xx/RV5VH2xx
Voltage Detector
Symbol Item Conditions MIN. TYP.
VOUT1=3.0V, Topt=25C
MAX.
Unit
VDET VHYS ISS3 VINmax VOPTmin IOUT ISEN
Detector Threshold Detector Threshold Hysteresis Supply Current3*1 Maximum Input Voltage Minimum Operating Voltage*2 VDS=0.5V, VOUT1=1.5V Output Current VDS=0.5V, VOUT1=3.0V Sensing Pin Input Current Output Delay DetectorThresholdTemp.Coefficient DOUT Leakage Current -40CTopt85C VSEN=3.0V
2.633 0.081
2.700 0.135 1.2
2.767 0.189
V V A
10 1.8 1.0 4.0 2.0 5.0 0.3 1.2 100 100 0.03 0.5
V V mA mA A s ppm/C A
tPLH
VOUT1 Topt IDOUTleak
* ) VOUT1=3.0V : unless otherwise specified. (See Typical Application) *1 ) This value only shows the supply current of voltage detector. *2 ) "Minimum Operating Voltage"means a voltage for the "VOUT1" pin.
14
RV5VH1xx/RV5VH2xx
* RV5VH202 DC/DC Converter 1
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VOUT1 VINmax Vstart Vhold ISS1 IEXT1H IEXT1L fosc Maxdty VOUT1 Topt
Step-up Output Voltage Maximum Input Voltage Oscillator Start-up Voltage Hold-on Input Voltage Supply Current1 *1 EXT1 "H" Output Current EXT1 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle Efficiency Output Voltage Temp. Coefficient
IOUT=0mA
4.875
5.000
5.125 10
V V V V
No Load IOUT=1mA IOUT=0mA, CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V 2 7 110 ON (VLX="L") 55 0.7
0.7
0.8
40 4 14 130 70 80 150 85
A mA mA kHz % % ppm/C
-40CTopt85C
100
* ) VIN=3.0V, IOUT=10mA : unless otherwise specified. (See Typical Application) *1 ) This value only shows the supply current of DC/DC1, does not include the supply current of Voltage Detector and external resistors.
15
RV5VH1xx/RV5VH2xx
DC/DC Converter 2
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VSET VFB VIN VOPTmin ISS2 Istandby IEXT2H IEXT2L fosc Maxdty VCSWH VCSWL ICSWleak VFB Topt
Output Voltage Setting Range Feed Back Voltage Maximum Input Voltage Minimum Operating Voltage*2 Supply Current2*3 Standby Current EXT2 "H" Output Current EXT2 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle CSW "H" Input Voltage CSW "L" Input Voltage CSW Input Leakage Current Feed Back Voltage Temp.Coefficient VEXT2="H" VOUT1=5.0V VOUT1=5.0V CSW=5.0V -40CTopt85C IOUT=1mA CSW= "H", No Load CSW="L" VEXT2=VOUT1-0.4V VEXT2=0.4V
*1 0
0
V mV
10 1.8 25 0.3 3 7 110 40 1.6 0 -0.5 30 6 14 130 50 150 60 VOUT1 0.4 0.5
V V A A mA mA kHz % V V A V/C
* ) VOUT1=5.0V, VOUT2=-3.0V, IOUT2=1mA : unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors to -30V. *2 ) "Minimum Operating Voltage"means a voltage for the "VOUT1" pin. *3 ) This value shows only the supply current of DC/DC2, not include the supply current of external resistors.
16
RV5VH1xx/RV5VH2xx
Voltage Detector
Symbol Item Conditions MIN. TYP.
VOUT1=5.0V, Topt=25C
MAX.
Unit
VDET VHYS ISS3 VINmax VOPTmin IOUT ISEN
Detector Threshold Detector Threshold Hysteresis Supply Current3*1 Maximum Input Voltage Minimum Operating Voltage*2 VDS=0.5V, VOUT1=1.5V Output Current VDS=0.5V, VOUT1=5.0V Sensing Pin Input Current Output Delay Detector Threshold Temp.Coefficient DOUT Leakage Current -40CTopt85C VSEN=5.0V
4.388 0.135
4.500 0.225 1.8
4.612 0.315
V V A
10 1.8 1.0 7.0 2.0 10.0 0.7 2.0 100 100 0.03 0.5
V V mA mA A s ppm/C A
tPLH
VOUT1 Topt IDOUTleak
* ) VOUT1=5.0V : unless otherwise specified. (See Typical Application) *1 ) This value only shows the supply current of voltage detector. *2 ) "Minimum Operating Voltage"means a voltage for the "VOUT1" pin.
17
RV5VH1xx/RV5VH2xx
OPERATION
* DC/DC Converter 1
RV5VH1xx Vref + - Error Amp.1 VLX lim. VFM1 3 R SBD 4 LX1 L C VOUT1 VOUT1
OSC
p_shift
VIN
RV5VH2xx Vref VOUT1 OSC + - Error Amp.1 3 R SBD EXT1 Rb NPN Tr. Cb VIN L1 C VOUT1
p_shift VFM1
4
The DC/DC1 uses input voltage as an initial power supply, once boost operation is started, the boost output will be used for the power supply of device itself. A change in the VOUT1 will feed back to the internal error amplifier through external voltage setting resistors and internal feed back resistors. When the feed back voltage is lower than the reference voltage the error amplifier enables oscllation or otherwise will stop oscillation. The internal feed back resistor "R" which is fixed and adjusted by laser trim can make the feed back input voltage to "Error Amp.1" stable. Pulses from the "OSC" circuit have a duty cycle of 50% and it becomes 65 to 75%(at high side) through the "P_shift" circuit. The duty cycle may be smaller with light load spontaneously. These clook pulses control VFM circuit and make it possible to operate as a boost converter. The output of LX1 is Nch open drain, while the output of "EXT1" is driven by CMOS buffer and an external NMOS driver is also available instead of an NPN transistor, in such cases the Rb and the Cb are not necessary. A recommended Rb is 300. When you use a MOSFET for the EXT1, the input voltage should be high enough and you can get high effiiciency applications. A current limit is available only for the RV5VH1 series, to prevent an excess current from flowing through Nch driver transistor. The DC/DC1 can be shut down by CSW pin. When the CSW pin is High, VDD level, the DC/DC1 is enabled and when the CSW pin is "L", GND level, the DC/DC1 is disabled. The EXT1 pin outputs "L" while the DC/DC1 is disabled.
18
RV5VH1xx/RV5VH2xx
* DC/DC Converter 2
RV5VH1xx/RV5VH2xx 1 FB - OSC + Error Amp.2 7 C2 PMOS EXT2 VFM2 6 L + C1 SBD VOUT2 R2 R1 CSW VOUT1
The DC/DC2 can operate by a voltage of "VOUT1". A change in the VOUT2 will feed back to the internal error amplifier through external voltage setting resistors. The reference voltage should be provided from externally fixed power supply such as VOUT1. When the feed back voltage to the cmp2 is higher than the ground voltage the error amplifier enables oscillation or otherwise will stop oscillation. Pulses from the "OSC" circuit have a duty cycle of 50% and it makes VFM operation allowable. There might be certain cases that the duty cycles becomes smaller temporarily at light load current. The output of "EXT2" is driven by CMOS buffer operated VOUT1 and GND. A PMOS driver will be connected to the "EXT2" pin and its switching operation generates negative output voltage through energy accumulated in an inductor. The DC/DC1 can be shut down by CSW pin. When the CSW pin is "H", VDD level, the DC/DC1 is enabled and when the CSW pin is "L", GND level, the DC/DC1 is disabled. The EXT2 pin outputs High while the DC/DC2 is disabled.
* Set output voltage DC/DC Converter2 VOUT2 is described as follows: VOUT1:R1=|-VOUT2| : R2 |-VOUT2|=VOUT1 x R2/R1 thus, any output voltage of DC/DC2 can be set by changing R1 or/and R2. Certain temperature coefficient of VOUT2 can be set by using R1,R2 having such temperature characteristics. / The FB voltage is controlled to 0V and VOUT1 is provided externally
19
RV5VH1xx/RV5VH2xx
* Voltage Detector
RV5VH1xx/RV5VH2xx 2 Ra Output Tr. Rb Vref Tr.1 Rc + - 8 DOUT VSEN
Pull-up
The VD can operate by the voltage of "VOUT1". The detector threshold and the reset voltage are internally adjusted by trimmed resistors and the VD monitors VSEN pin voltage. The DOUT is Nch open-drain output and a pull up resistor is necessary.
Oepration Diagram VSEN pin is pulled up to VOUT1 voltage
Step
1 2 3 4 5
Step 1
Step 2
Step 3
Step 4
Step 5
Reset Voltage +VDET Detector Threshold -VDET
B Hysteresis Range A
Comparator(+) Pin Input Voltage Comparator Output Tr. 1
A H OFF OFF
B L ON ON
B L ON
Indefinite
B L ON ON
A H OFF OFF
GND
Output Tr
Output Voltage
A:
GND
Rb+Rc Ra+Rb+Rc Rb Ra+Rb+Rc
x VSEN x VSEN
B:
Step 1. Output Voltage is equal to Pull-up Voltage. Step 2. When Input voltage (VSEN) reaches the state of VrefVSENx(RbxRc)/(Ra+Rb+Rc) at point A, the output of the comparator is reversed. so that the output voltage becomes to GND. Step 3. Output VoItage becomes indefinite when Power source Voltage (VSEN) is smaller than Minimum Operating VoItage. When the output is pulIed up, Output becomes pull-up voltage and GND. Step 4. Output VoItage becomes to GND. Step 5. When input voltage(VSEN) reaches the state of VrefVSENxRb/(Ra+Rb) at point B, the output of the comparator is reversed, so that the output voltage becomes to pull-up voltage.
20
RV5VH1xx/RV5VH2xx
OPERATION OF STEP-UP DC/DC CONVERTER
Step-up DC/DC Converter charges energy in the inductor when Lx Transistor (LxTr) is on, and discharges the energy with the addition of the energy from Input Power Source thereto, so that a higher output voltage than the input voltage is obtained. The operation will be explained with reference to the following diagrams :
< Basic Circuits > < Current through L >
IL i2 L VIN i1 Lx Tr CL SD IOUT VOUT ton T=1/fosc toff ILmin ILmax topen
t
Step 1 : LxTr is turned ON and current IL (=i1 ) flows, so that energy is charged in L. At this moment, IL(=i1 ) is increased from ILmin (=0) to reach ILmax in protection to the on-time period (ton) of LxTr. Step 2 : When LxTr is turned OFF, Schottky diode (SD) is turned on in order that L maintains IL at ILmax, so that current IL (=i2) is released. Step 3 : IL (=i2) is gradually decreased, and IL reaches ILmin (=0) after a time period of topen, so that SD is turned OFF. In the case of VFM control system, the output voltage is maintained constant by controlling the oscillator frequency (fosc) with the on-time period (ton) being maintained constant. In the above two diagrams, the maximum value (ILmax) and the minimum value (ILmin) of the current which flows through the inductor are the same as those when LxTr is ON and also when LxTr is OFF. The difference between ILmax and ILmin, which is represented by I, is: I=ILmax-ILmin=VIN * ton/L=(VOUT-VIN) * topen/L ..........................................Equation 1 wherein T=1/fosc=ton+toff duty (%)=ton/T * 100=ton * fosc * 100 topentoff In Equation 1,VIN * ton/L and (VOUT-VIN) * topen/L are respectively the change in the current at ON, and the change in the current at OFF. In the VFM system, topen < toff as illustrated in the above diagram. In this case, the energy charged in the inductor during the time period of ton is discharged in its entirely during the time period of toff, so that ILmin becomes zero (ILmin=0).
21
RV5VH1xx/RV5VH2xx
SELECTION OF PERIPHERAL COMPONENTS
When LxTr is on, the energy PON charged in the inductor is provided by Equation 2 as follows :
ton ton PON= 0 (VIN * IL (t)) dt= 0 (VIN2 * t/L) dt =VIN2 * ton2/(2 * L).................................................................................................... Equation 2
In the case of the step-up DC/DC converter, the energy is also supplied from the input power source at the time of OFF.
topen topen (VIN * (VOUT-VIN) * t/L)dt Thus, POFF = 0 (VIN * IL (t)) dt= 0 =VIN * (VOUT-VIN) * topen2/(2 * L)
Here, topen=VIN * ton/(VOUT-VIN) from Equation 1, and when this is substituted into the above equation. =VIN3 * ton2/(2 * L * (VOUT-VIN)) ............................................................................Equation 3 Input power PIN is (PON+POFF)/T. When this is converted in its entirely to the output. PIN=(PON+POFF)/T=VOUT * IOUT=POUT .........................................................................Equation 4 Equation 5 can be obtained as follows by solving Equation 4 for IOUT by substituting Equation 2 and 3 into Equation 4 : IOUT=VIN2 * ton2/(2 * L * T * (VOUT-VIN) =VIN2 * maxdty2/(20000 * fosc * L * (VOUT-VIN)) ...................................................Equation 5 The peak current which flows through L * LxTr * SD is ILmax=VIN * ton/L .......................................................................................................... Equation 6 Therefore, it is necessary that the setting of the input/output conditions and the selection of peripheral components be made with ILmax taken into consideration.
HINTS
The above explanation is directed to the calculation in an ideal case where it is supposed that there is no energy loss in the external components and LxSW. In an actual case, the maximum output current will be 50 to 80% of the above calculated maximum output current. In particular, care must be taken because VIN is decreased in an amount corresponding to the voltage reduction caused by LxSW when IL is large or VIN is small. Furthermore, It is required that with respect to VOUT, Vf of the diode (about 0.3V in the case of a Schottky type diode) be taken into consideration. When ILX and VLX exceed their respective ratings, use the RV5VH with the attachment of an external transistor with a low saturation voltage thereto.
22
RV5VH1xx/RV5VH2xx
TYPICAL APPLICATION
* RV5VH1xx
R3 CSW VSEN Output DC/DC1 VOUT1 D1 LX1 L1 C1 L2 GND EXT2 D2 Output DC/DC2 C2 DOUT FB PMOS R2 C3 R1

CoiIs Diodes Capacitors Tr Resistors
L1 : 100H, L2 : 220H Schottky type C1, C2 : 22F(tantalum type), C3 : 0.01F(ceramic type) PMOS : 2SJ238 R1, R2 : several hundreds k, R3 : 100k
* RV5VH2xx
R3 CSW VSEN Output DC/DC1 VOUT1 L1 SBD C4 C1 NPN Tr. R4 EXT1 GND L2 EXT2 SBD Output DC/DC2 C2 DOUT FB PMOS R2 C3 R1

Coils Diodes Capacitors
PMOS NPN Tr. Resistors
L1 : 27H, L2 : 220H Schottky type C1 : 47F(tantalum type), C2 : 22F(tantalum type) C3 : 0.01F(ceramic type) C4 : 0.01F(ceramic type) 2SJ238(TOSHIBA), etc. 2SD1628G(SANYO), etc. R1 : 100K R2 : 0-500K R3 : 100K R4 : 300
23
RV5VH1xx/RV5VH2xx
TEST CIRCUITS
CSW VSEN VOUT1 LX1 22F V A L1
DOUT FB EXT2 GND L1=100H,220H
Fig.1
Test Circuit 1
100k CSW VSEN 5 (150) * V VOUT1 LX1(EXT1) DOUT FB EXT2 GND V 150 A
Oscilloscope Fig.2 Test Circuit 2
* EXT1
CSW VSEN VOUT1 LX1
DOUT FB EXT2 GND
A
0.5V
Fig.3
Test Circuit 3
24
RV5VH1xx/RV5VH2xx
100k CSW VSEN VOUT1 LX1 DOUT FB EXT2 GND Oscilloscope Pulse Input Fig.4 Test Circuit 4
CSW VSEN 2200pF 96F V A 27H 300 VOUT1 EXT1
DOUT FB EXT2 GND
Fig.5
Test Circuit 5
Test Circuit 1: Test Circuit 2: Test Circuit 3: Test Circuit 4: Test Circuit 5:
Typical Characteristics 1), 3), 5), 10), 11) Typical Characteristics 6), 7), 8), 9), 13), 14), 15), 16), 17), 18), 19), 21) Typical Characteristics 20) Typical Characteristics 22) Typical Characteristics 2), 4)
Typical Application : Typical Characteristics 12)
25
RV5VH1xx/RV5VH2xx
TYPICAL CHARACTERISTICS
* DC/DC Converter 1 1) Output Voltage vs. Output Current (RV5VH1xx)
RV5VH101
3.6
Topt=25C L1=100H C1=22F Output Voltage VOUT1(V)
RV5VH101
3.6 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 0 20 40 60 80 VIN=1.2V
Topt=25C L1=220H C1=22F
Output Voltage VOUT1(V)
3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 0 20 40 60 80 100 120 140 VIN=0.9V VIN=1.2V VIN=1.5V VIN=2.0V
VIN=2.0V VIN=0.9V VIN=1.5V
100
120
140
Output Current IOUT(mA)
Output Current IOUT(mA)
RV5VH102
6.0
Topt=25C L1=100H C1=22F Output Voltage VOUT1(V)
RV5VH102
6.0 5.5 5.0 VIN=1.5V 4.5 4.0 3.5 3.0 VIN=0.9V VIN=2.0V VIN=3.0V
Topt=25C L1=220H C1=22F
Output Voltage VOUT1(V)
5.5 5.0 4.5 4.0 3.5 3.0 0 50 100 150 200 250 300 VIN=1.5V VIN=2.0V VIN=0.9V VIN=3.0V VIN=4.0V
VIN=4.0V
0
50
100
150
200
250
300
Output Current IOUT(mA)
Output Current IOUT(mA)
2) Output Voltage vs. Output Current (RV5VH2xx)
RV5VH201
3.6 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 0 100 200 300 400 500 VIN=0.9V VIN=1.2V VIN=1.5V VIN=2.0V
Topt=25C L1=27H C1=96F Output Voltage VOUT(V)
RV5VH202
6.0 5.5 5.0 VIN=1.5V 4.5 4.0 3.5 3.0 0 100 200 300 VIN=0.9V
Topt=25C L1=27H C1=96F
Output Voltage VOUT(V)
VIN=4.0V VIN=2.0V VIN=3.0V
400
500
Output Current IOUT(mA)
Output Current IOUT(mA)
26
RV5VH1xx/RV5VH2xx
3) Efficiency vs. Output Current (RV5VH1xx)
RV5VH101
100 95 90
Topt=25C L1=100H C1=22F
RV5VH101
100 95 90 VIN=1.5V VIN=2.0V
Topt=25C L1=220H C1=22F
Efficiency (%)
80 75 70 65 60 55
VIN=1.2V
VIN=2.0V
Efficiency (%)
85
85 80 75 70 65 60 55 VIN=0.9V VIN=1.2V 0.1 1 10 100
VIN=0.9V VIN=1.5V 0.1 1 10 100
50 0.01
50 0.01
Output Current IOUT(mA) Topt=25C L1=100H C1=22F
Output Current IOUT(mA) Topt=25C L1=220H C1=22F
RV5VH102
100 95 90
RV5VH102
100 95 90
Efficiency (%)
Efficiency (%)
85 80 75 70 65 60 55 50 0.1 1 10 VIN=1.5V VIN=0.9V
VIN=4.0V
85 80 75 70 65 60 55 50 0.1 VIN=1.5V VIN=0.9V
VIN=4.0V
VIN=3.0V
VIN=3.0V
VIN=2.0V
VIN=2.0V 1 10 100 1000
100
1000
Output Current IOUT(mA)
Output Current IOUT(mA)
4) Efficiency vs. Output Current (RV5VH2xx)
RV5VH201
90 85 80 VIN=1.5V VIN=1.2V
Topt=25C L1=27H C1=96F
RV5VH202
90 85 VIN=4.0V VIN=3.0V VIN=2.0V VIN=1.5V 80
Topt=25C L1=27H C1=96F
VIN=2.0V
Efficiency (%)
Efficiency (%)
75 70 65 60 55 50 45 40 0.01 0.1 1 10 100 1000 VIN=0.9V
75 70 65 60 55 50 45 40 0.1
VIN=0.9V
1
10
100
1000
Output Current IOUT(mA)
Output Current IOUT(mA)
27
RV5VH1xx/RV5VH2xx
5) DC/DC1 Output Voltage vs. Temperature
RV5VH1xx/2xx
3.3
VIN=1.2V L1=100H C1=22F Output Voltage VOUT(V)
RV5VH1xx/2xx
5.3 5.2 5.1 5.0 4.9 4.8 IOUT=0A IOUT=1mA IOUT=10mA
VIN=3V L1=100H C1=22F
Output Voltage VOUT(V)
3.2 3.1 3.0 2.9 2.8 2.7 -60 -40 -20 IOUT=10mA IOUT=5mA IOUT=0A
0
20
40
60
80
100
4.7 -60 -40 -20
0
20
40
60
80
100
Temperature Topt(C)
Temperature Topt(C)
6) Oscillator Frequency vs. Temperature
RV5VH1xx/2xx
150
VOUT1=3V Oscillator Frequency fosc(kHZ)
RV5VH1xx/2xx
150 145 140 135 130 125 120 115 110 105 100 -60 -40 -20 0 20 40
VOUT1=5V
Oscillator Frequency fosc(kHZ)
145 140 135 130 125 120 115 110 105 100 -60 -40 -20 0 20 40 60 80 100
60
80
100
Temperature Topt(C)
Temperature Topt(C)
7) Oscillator Duty Cycle vs. Temperature
RV5VH1xx/2xx
Oscillator Duty Cycle Maxdty(%)
80 75 70 65 60 55 50 -60 -40 -20
VOUT1=3V Oscillator Duty Cycle Maxdty(%)
RV5VH1xx/2xx
80 75 70 65 60 55 50 -60 -40 -20
VOUT1=5V
0
20
40
60
80
100
0
20
40
60
80
100
Temperature Topt(C)
Temperature Topt(C)
28
RV5VH1xx/RV5VH2xx
8) On Resistance of LX vs. Supply Voltage
RV5VH1xx
5.0 4.5 85C 25C -40C
On Resistance Ron ()
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.0
1.0
2.0
3.0
4.0
5.0
6.0
Supply Voltage VOUT1(V)
9) EXT1 Output Current vs. Temperature
RV5VH201
18 16 14 12 10 8 6 4 2 0 -60 -40 -20 0 20 40 60 80 100 "H" Output Current "L" Output Current
VOUT1=3V Output Current IOUT(mA)
RV5VH202
18 16 14 12 10 8 6 4 2 0 -60 -40 -20 0 20 40 "H" Output Current "L" Output Current
VOUT1=5V
Output Current IOUT(mA)
60
80
100
Temperature Topt(C)
Temperature Topt(C)
10) Start-up/Hold-on Voltage vs. Output Current
Topt=25C VOUT1=3V L1=100H C1=22F
11) Input Current vs. Intput Voltage
Topt=25C CSW=GND L1=100H C1=22F
Start-up/Hold-on Voltage Vstart/Vhold(V)
RV5VH1xx/2xx
2 1.8 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 10 20 30 Vhold 1.6
RV5VH101
10-0 10-1 IOUT=30mA IOUT=5mA IOUT=1mA
Input Current IIN(A)
Vstart
10-2 10-3 10-4 10-5 10-6 0.0
IOUT=0A
40
50
0.5
1.0
1.5
2.0
2.5
3.0
Output Current IOUT(mA)
Input Voltage VIN(V)
29
RV5VH1xx/RV5VH2xx
* DC/DC Converter 2 12) Output Voltage vs. Output Current
RV5VH101
0 -2 -4 -6 -8 -10 VSET -12V -12 -14 0 2 4 6 8 10 12 14 VSET -6V
Topt=25C VIN=1.2V VOUT1=3V
VSET -3V
Output Voltage VOUT(V)
VSET -9V
Output Current IOUT(mA)
13) DC/DC2 Feed Back Voltage vs. Temperature
RV5VH1xx/2xx
0.010
Feed Back Voltage VFB(V)
0.008 0.006 0.004 0.002 0.000 -0.002 -0.004 -0.006 -0.008 -0.010 -60 -40 -20 0 20 40 60 80 100
Temperature Topt(C)
14) EXT2 Output Current vs. Temperature
RV5VH1xx/2xx
20 18
VOUT1=3V Output Current IOUT(mA)
RV5VH1xx/2xx
20 18 16 14 12 10 8 6 4 2 0 -60 -40 -20 "H" Output Current "L" Output Current
VOUT1=5V
Output Current IOUT(mA)
16 14 12 10 8 6 4 2 0 -60 -40 -20 0 20 40 60 80 100 "H" Output Current "L" Output Current
0
20
40
60
80
100
Temperature Topt(C)
Temperature Topt(C)
30
RV5VH1xx/RV5VH2xx
15) EXT2 Oscillator Frequency vs. Temperature
RV5VH1xx/2xx
150
VOUT1=3V Oscillator Frequency fosc(kHZ)
RV5VH1xx/2xx
150 145 140 135 130 125 120 115 110 105 100 -60 -40 -20 0 20 40
VOUT1=5V
Oscillator Frequency fosc(kHZ)
145 140 135 130 125 120 115 110 105 100 -60 -40 -20 0 20 40 60 80 100
60
80
100
Temperature Topt(C)
Temperature Topt(C)
16) EXT2 Oscillator Duty Cycle vs. Temperature
RV5VH1xx/2xx
Oscillator Duty Cycle Maxdty(%)
60 58 56 54 52 50 48 46 44 42 40 -60 -40 -20 0 20 40 60 80 100
VOUT1=3V Oscillator Duty Cycle Maxdty(%)
RV5VH1xx/2xx
60 58 56 54 52 50 48 46 44 42 40 -60 -40 -20 0 20 40
VOUT1=5V
60
80
100
Temperature Topt(C)
Temperature Topt(C)
17) CSW ON/OFF Voltage vs. Temperature
RV5VH1xx/2xx
2.0
VOUT1=3V
CSW ON/OFF Voltage (V)
1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -60 -40 -20 0 20 40 60 80 100
Temperature Topt(C)
31
RV5VH1xx/RV5VH2xx
* Voltage Detector 18) Detector Threshold Voltage vs. Temperature
RV5VH1xx/2xx
Detector Threshold Voltage VDET(V)
3.0
19) VOUT1 Output Voltage vs. Output Current
RV5VH1xx/2xx
5.0 4.5
Output Current VOUT(V)
2.9 2.8 2.7 2.6
+VDET
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 85C -40C 25C
-VDET
2.5 -60 -40 -20
0
20
40
60
80
100
0
1
2
3
4
5
Temperature Topt(C)
VOUT1 Output Voltage VOUT1(V)
20) DOUT Output Current vs. VOUT1 Output Voltage
RV5VH1xx/2xx
DOUT Output Current IDOUT(mA)
20 18 16 14 12 10 8 6 4 2 0 0 1 2 3 4 5 6 7 85C 25C -40C
21) VSEN Output Current vs. VSEN Output Voltage
RV5VH1xx/2xx
0.7
VSEN Output Current IVSEN(A)
0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 85C
25C -40C
VOUT1 Output Voltage VOUT1(V)
VSEN Output Voltage VSEN(V)
22) Output Delay Time vs. Load Capacitance
RV5VH1xx/2xx
10
VOUT1=3V
Output Delay Time tp(ms)
1
tPLH
0.1
tPHL
0.01 0.0001
0.001
0.01
0.1
Load Capacitance COUT(F)
32
DC/DC CONVERTER CONTROLLER (BOOST / INVERTING OUTPUT FOR LCD)
RV5VH3xx
BLOCK DIAGRAM
CSW 1 - + 8 DOUT
FB1 2
Vref Error Amp.2
- +
7 FB2
VDD 3
- + Error Amp.1
VFM2
6 EXT2
EXT1 4 VFM1
p_shift
5 GND OSC
PIN CONFIGURATION
* 8 pin SSOP (0.65mm pitch)
1 2 3 4 8 7 6 5
33
RV5VH3xx
PIN DESCRIPTION
Pin No. Symbol Description
1 2 3 4 5 6 7 8
CSW FB1 VDD EXT1 GND EXT2 FB2 DOUT
Control Switch for DC/DC1, 2 Input for DC/DC1 Error Amplifier Power Supply for Device Itself. Sensing Pin for Reset. External Transistor Drive Pin for DC/DC1 (CMOS Output) Ground Pin External Transistor Drive Pin for DC/DC2 (CMOS Output) Input for DC/DC2 Error Amplifier Output for Voltage Detector
ABSOLUTE MAXIMUM RATINGS
Symbol Item Ratings
GND=0V
Unit
VDD DOUT VCSW VEXT1, 2 VFB IEXT1, 2 PD Topt Tstg Tsolder
VDD Pin Voltage DOUT Pin Voltage CSW Pin Voltage EXT1, 2 Pin Voltage FB1,2 Pin Voltage EXT1, 2 Output Current Power Dissipation Operating Temperature Storage Temperature Lead Temperature (Soldering)
12 12 -0.3 to VDD+0.3 -0.3 to VDD+0.3 -0.3 to VDD+0.3 50 300 -40 to +85 -55 to +125 260C 10sec
V V V V V mA m C C
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum ratings are threshold limit values that must not be exceeded even for an instant under any conditions. Moreover, such values for any two items must not be reached simultaneously. Operation above these absolute maximum ratings may cause degradation or permanent damage to the device. These are stress ratings only and do not necessarily imply functional operation below these limits.
34
RV5VH3xx
ELECTRICAL CHARACTERISTICS
* RV5VH301 DC/DC Converter 1
Symbol Item Conditions MIN. TYP.
VDD=3.0V, Topt=25C
MAX.
Unit
VSET1 VFB1 VINmax VOPTmin ISS11 ISS12 Istandby IEXT1H IEXT1L fosc Maxdty VFB1 Topt VCSWH VCSWL ICSWleak
Output Voltage Setting 1 Feed Back Volatage 1 Maximum Input Voltage Minimum Operating Voltage Supply Current11*2 Supply Current12*2 Standby Current*3 EXT1 "H" Output Current EXT1 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle Feed Back Voltage Temp.Coefficient CSW "H" Input Voltage CSW "L" Input Voltage CSW Input Leakage Current CSW=3.0V or CSW=0V ON (VEXT1="L") -40CTopt85C Specified as a VDD Voltage for Device Operation CSW="H", FB1=1.9V CSW="H", FB1=2.1V CSW="L" VEXT1=VDD-0.4V VEXT1=0.4V
2.05 1.950 2.000
*1 2.050 10 1.8 15 4 4 11 60
V V V V A A A mA mA
1.5 4 110 50
3 8 130 65 100 150 80
kHz % ppm/C
1.6 0 -0.5
VDD 0.4 0.5
V V A
* ) VDD=3.0V, IOUT=10mA : unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors (to 30V). *2 ) Supply current for DC/DC1. Supply current for VD or external resistors are excluded. *3 ) Standby current includes supply current for DC/DC1, 2 and VD.
35
RV5VH3xx
DC/DC Converter 2
Symbol Item Conditions MIN. TYP.
VDD=3.0V, Topt=25C
MAX.
Unit
VSET2 VFB2 VINmax VOPTmin ISS21 ISS22 IEXT2H IEXT2L fosc Maxdty VFB2 Topt
Output Voltage Setting 1 Feed Back Volatage 1 Maximum Input Voltage Minimum Operating Voltage Supply Current21*2 Supply Current22*2 EXT2 "H" Output Current EXT2 "L" Output Current Maximum Oscillator Frequency Oscillator Duty Cycle Feed Back Voltage Temp.Coefficient ON (VEXT2="L") -40CTopt85C Specified as the VDD Voltage for Device Operation CSW="H", FB2=0.1V CSW="H", FB2=-0.1V VEXT2=VDD-0.4V VEXT2=0.4V
*1 -20 0
0 20 10 1.8 15 4 60
V mV V V A A mA mA
2 4 110 40
4 8 130 50 30 150 60
kHz % V/C
* ) VDD=3.0V : unless otherwise specified. (See Typical Application) *1 ) Adjustable by external resistors (to -30V). *2 ) This value shows only the supply current of DC/DC2, not include the supply current of external resistors.
36
RV5VH3xx
Voltage Detector
Symbol Item Conditions MIN. TYP.
VDD=3.0V, Topt=25C
MAX.
Unit
VDET VHYS ISS3 VINmax VOPTmin
Detector Threshold Detector Threshold Hysteresis Supply Current3*1 Maximum Input Voltage Minimum Operating Voltage Specified as the VDD Voltage for Device Operation VDS=0.5V, VDD=1.5V
2.633 0.081
2.700 0.135 1.2
2.767 0.189
V V A
10 1.8 1.0 4.0 2.0 5.0 100 -40CTopt85C 100 0.03 0.5
V V mA mA s ppm/C A
IOUT
Output Current VDS=0.5V, VDD=3.0V Output Delay Detector Threshold Temp.Coefficient DOUT Leakage Current
tPLH
VOUT1 Topt IDOUTleak
* ) VDD=3.0V : unless otherwise specified. *1 ) This value only shows the supply current of voltage detector.
37
RV5VH3xx
OPERATION
* DC/DC Converter 1
RV5VH3xx 3 CSW 1 Vref + OSC - Error Amp.1 p_shift 4 VFM1 Cb VIN EXT1 Rb NPN Tr. 2 R2 FB1 R1 SBD L1 C VOUT1 VDD
The DC/DC1 can operate by an input voltage to the VDD pin. A change in the VOUT1 will feed back to the internal error amplifier through external voltage setting resistors and internal feed back resistors. When the feed back voltage is lower than the reference voltage, the error amplifier enables oscillation or otherwise, it will stop oscillation. The internal feed back resistor "R" which is fixed and adjusted by laser trim can make the feed back input voltage to "Error Amp.1" stable. Pulses from the "OSC" circuit have a duty cycle of 50% and it becomes 65 to 75%(at high side) through the "P_shift" circuit. These clock pulses control VFM circuit and make it possible to operate as a boost converter. The output of "EXT1" is driven by CMOS buffer and an external NMOS driver is also available instead of an NPN transistor, in such cases the Rb and the Cb are not necessary. The DC/DC1 can be shut down by CSW pin. When the CSW pin is "H", VDD level, the DC/DC1 is enabled and when the CSW pin is "L", GND level, the DC/DC1 is disabled. The EXT1 pin outputs "L" while the DC/DC1 is disabled.
* Set Output Voltage DC/DC1 VOUT1 is described as follows : VOUT1 : R1+R2=VFB1 : R2 VOUT1=VFB1 x (R1+R2) / R2 thus, any output voltage of DC/DC1 can be set by changing R1 or/and R2. Certain temperature coefficient of VOUT1 can be set by using R1, R2 having such temperature characteristics. DC/DC1 controls VFB1 to be a constant voltage,
38
RV5VH3xx
* DC/DC Converter 2
RV5VH3xx 1
CSW FB2
VDD
VREF R1 C2 R2
OSC
- + Error Amp.2
7
PMOS EXT2 SBD VOUT2 C1 6 L +
VFM2
The DC/DC2 can operate by an input voltage to the VDD pin. A change in the VOUT2 will feed back to the internal error amplifier through external voltage setting resistors. The VREF voltage should be provided from externally fixed power supply such as VOUT1. When the feed back voltage to the Error Amp.2 is higher than the ground voltage, the error amplifier enables oscillation otherwise, it will stop oscillation. Pulses from the "OSC" circuit have a duty cycle of 50% and it makes VFM operation allowable. There might be certain cases that the duty cycles become smaller temporarily at light load current. The output of "EXT2" is driven by CMOS buffer operated VDD and GND. A PMOS driver will be connected to the "EXT2" pin and its switching operation generates negative output voltage through energy accumulated in an inductor. The DC/DC1 can be shut down by CSW pin. When the CSW pin is High, VDD level, the DC/DC1 is enabled and when the CSW pin is "L", GND level, the DC/DC1 is disabled. The EXT2 pin outputs "H" while the DC/DC2 is disabled.
* Set Output Voltage DC/DC 2 VOUT2 is described as follows: VREF : R1=|-VOUT2| : R2 |-VOUT2|=VREFxR2/R1, thus, any output voltage of DC/DC2 can be set by R1 and R2. Certain temperature coefficient of VOUT2 can be set by using R1, R2 having such temperature characteristics. The FB2 voltage is controlled to 0V and VREF is provided externally
39
RV5VH3xx
* Voltage Detector
RV5VH3xx 3 VDD R1 Output Tr. R2 Vref Tr.1 R3 + - 8 DOUT Pull-up
The Voltage Detector can operate by an input voltage to the VDD pin. The detector threshold and the reset voltage are internally adjusted by trimmed resistors and the VD monitors VDD pin voltage. The DOUT is Nch open-drain output and a pull up resistor is necessary.
Oepration Diagram The output is pulled up to VDD voltage
Step
1 2 3 4 5
Step 1
Step 2
Step 3
Step 4
Step 5
Reset Voltage +VDET Detector Threshold -VDET
B Hysteresis Range A
Comparator(+) Pin Input Voltage Comparator Output Tr. 1
A H OFF OFF
B L ON ON
B L ON
Indefinite
B L ON ON
A H OFF OFF
GND
Output Tr.
Output Voltage
A:
GND
R2+R3 R1+R2+R3 R2 R1+R2+R3
x VDD x VDD
B:
Step 1. Output Voltage is equal to Pull-up Voltage Step 2. When Input voltage(VDD) reaches to the state of VREFVDDx(R2+R3)/(R1+R2+R3) at point A, the output of the comparator is reversed, so that the output voltage becomes to GND. Step 3. Output Voltage becomes indefinite when Power Source Voltage (VDD) is smaller than Minimum Operating Voltage. When the output is pulIed up, Output becomes pull-up voltage and GND. Step 4. Output Voltage becomes to GND. Step 5. When Input voltage(VDD) reaches to the state of VREFVDDxR2/(R1+R2) at point B, the output of the comparator is reversed, so that the output voltage becomes to pull-up voltage.
40
RV5VH3xx
TYPICAL APPLICATION 1
Output DC/DC 1
R5
C5 CSW DOUT FB2
R3 R1
R6 SBD L1 VDD R4 NPN Tr. C1 C4 EXT1 GND Output DC/DC 2 L2 C2 EXT2 SBD FB1 PMOS R2 C3
CoiI Diode capacitor
PMOS NMOS Resistor
L1 : 100H, L2 : 100H Schottky type C1 : 22F(Ta), C2 : 22F(Ta) C3 : 0.01F (ceramic) C4 : 0.01F (ceramic) C5 : 0.01F (ceramic) 2SJ238 (TOSHIBA) 2SK1470 (SANYO) R1 : 100k , R2 : 0 to 500k R3 : 100k R4 : 300 R5 : 0 to 500k, R6 : 50k
41
RV5VH3xx
TYPICAL APPLICATION 2
VIN Output DC/DC 1 R5 C5 CSW R6 SBD L1 VDD R4 NPN Tr. C1 C4 EXT1 GND Output DC/DC 2 L2 C2 EXT2 SBD FB1 FB2 PMOS R2 C3 DOUT R3 R1
CoiI Diode capacitor
PMOS NPN Tr. Resistor
L1 : 100H, L2 : 100H Schottky type C1 : 22F(Ta), C2 : 22F(Ta) C3 : 0.01F (ceramic) C4 : 0.01F (ceramic) C5 : 0.01F (ceramic) 2SJ238 (TOSHIBA) 2SD1628G (SANYO) R1 : 100k , R2 : 0 to 500k R3 : 100k R4 : 300 R5 : 0 to 500k, R6 : 50k
Description * Step up DC/DC converter : DC/DC1 The oscillator can operate when CSW is "H". When the CSW is "L" the EXT1 outputs GND. The output voltage can be adjusted by R5 and R6 with FB1 of two volt. * Invering DC/DC converter : DC/DC2 The oscillator can operate when CSW is "H". When the CSW is "L" the EXT2 outputs VDD. The output voltage can be adjusted by R1 and R2 with FB2 of zero volt. * VoItage Detector VDD pin can be monitored. This could be always operated with VDD. The DOUT pin outputs "L" when low voltage is detected with Nch open-drain output.
42
RV5VH3xx
TYPICAL APPLICATION 3
VIN Output DC/DC 1
R3 R5 C5 PMOS CSW FB1 R6 L1 SBD1 VDD EXT1 NMOS C1 L2 EXT2 GND C4 Output DC/DC 2 C2 DOUT FB2 PNP Tr. R4 SBD3 R2 SBD2 C3 R1
R1 : 820k, R2 : 820k, R3 : 100k, R4 : 1k, R5 : 750k (AdjustabIe) R6 : 100k L1 : 68H, L2 : 27H C1 : 22F, C2 : 22F, C3 : 1000pF, C4 : 2200pF, C5 : 1000pF PMOS : 2SJ238, NMOS : 2SK1470, PNPTr. : 2SB1120F
Operation The VDD voltage can be supplied from another source than battery output and a reference voltage for DC/DC2 is supplied by the output of DC/DC1. The PMOS transistor can operate as a switch when the CSW is "L". * Step up DC/DC converter : DC/DC1 The oscillator can operate when CSW is "H". When the CSW is "L" the EXT1 outputs GND. The output voltage can be adjusted by R5 and R6 with FB1 of two volt. * Invering DC/DC converter : DC/DC2 The oscillator can operate when CSW is "H". When the CSW is "L" the EXT2 outputs VDD. The output voltage can be adjusted by R1 and R2 with FB2 of zero volt. * VoItage Detector VDD pin can be monitored. This could be operated all the time by VDD. The DOUT pin outputs "L" when low voltage is detected with Nch open-drain output.
43
RV5VH3xx
TYPICAL CHARACTERISTICS
1) Output Voltage vs. Output Current
25 20 VIN=3.6V
2) Efficiency vs. Output Current
100 90 VIN=3.6V 10V VOUT5.0V 15V
Output Voltage VOUT(V)
15 10 5 0 -5 -10 -15 -20 -25 0 10 20
Efficiency (%)
80 70 60 50 40 30 20 0.0001
20V
0.001
0.01
0.1
Output Current IOUT(mA)
Output Current IOUT(A)
3) CSW Load Transient Responce 1
20 VIN=3.6V, IOUT=1mA VOUT1
4) CSW Load Transient Responce 2
20 VIN=3.6V, IOUT=1mA VOUT1
Output Voltage VOUT(V)
10 5 0 -5 -10 -15 -20 -50 VOUT2 0 50 100 150 200 CSW
Output Voltage VOUT(V)
15
15 10 5 0 -5 -10 -15 -20 0
CSW
VOUT2
500
1000
1500
Time t(ms)
Time t(ms)
* ) Please refer to Typical Application.
44
RV5VH3xx
SELECTION GUIDE
The output voltage, the type of DC/DC1 and the taping type for the ICs can be selected at the user's request. The selection can be made by designating the part number as shown below: RV5VH xxx-xx Part Number ab
}
}
c
Code
Contents
DC/DC1 type a 1 : Internal LX Driver Transister Type 2 : External EXT Driver Transister Type 3 : Variable Output Voltage Type b c Serial (01, 02, 03) Number of Setting DC/DC1 Output Voltage and Setting VD Detect Voltage. Designation of Taping type Ex. E1, E2 (refer to Taping Specifications, E2 type is prescribed as a standard.)
45
RV5VH3xx
APPLICATION HINTS
When using these ICs, be sure to take care of the following points. * Set external components as close as possible to the IC and minimize the connection between the components and the IC. In particular, when an external component is connected to VOUT Pin, make minimum connection with the capacitor. * Make sufficient grounding. A large current flows through GND Pin byswitching. When the impedance of the GND connection is high, the potential within the IC is varied by switching current. This may result in unstableoperation of the IC. * Use capacitor with good high frequency characteristics such as tantalum capacitor, aluminium electrolytic capacitor and ceramic capacitor. We recommend the use of a capacitor with an allowable voltage which is at least three times the output set voltage. This is because there may be the case where a spike-shaped high voltage is generated by the inductor when Lx transistor is turned OFF. * Take the utmost care when choosing an inductor. Namely, choose such an inductor that has sufficiently small d.c. resistance and large allowable current, and hardly reaches magnetic saturation. When the inductance value of the inductor is small, there may be the case where ILX exceeds the absolute maximum ratings at the maximum load. Use an inductor with an appropriate inductance. (See OUTPUT CURRENT and SELECTION OF PERIPHERAL COMPONENTS sections.) * Use a diode of a Schottky type with high switching speed, and also take care of the rated current. (See OUTPUT CURRENT and SELECTION OF PERIPHERAL COMPONENTS sections.)
The performance of power source circuits using these ICs largely depends upon the peripheral components. Take the utmost care in the selection of the peripheral components. In particular, design the peripheral circuits in such a manner that the values such as voltage, current and power of each component, PCB patterns and the IC do not exceed their respective rated values.
46

▲Up To Search▲

Price & Availability of RV5VH

	To Download RV5VH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .